Batwing Tidig tillgång för VIP-medlemmarHandla nu

Batwing Tidig tillgång för VIP-medlemmarHandla nu

Item 1 of 1
Item 1 of 1
LEGO®88007Powered UPPowered UP

Färg- och avståndssensor

Average rating3.8out of 5 stars
Price149,00 kr

Tillgänglig nu

Gräns 20
Handla mer som detta:
7+Åldrar
1Delar
112
VIP-poäng
880078800788007Artikel
Anslut LEGO® Powered Up 88007 Färg- och avståndssensor till 88006 Rörelsehubb eller 88009 Hubb. Den här LEGO sensorn kan upptäcka färger och rörelse för att göra dina LEGO byggen och robotleksaker interaktiva.
  • Med sensor, anslutningskabel och anslutningspunkt till LEGO® Powered Up delar.
  • Upptäck 6 färger och föremål inom ett avstånd på 5 till 10 cm med detta robotleksakstillbehör för barn.
Bygginstruktioner
Färg- och avståndssensor
  • Gratis standardleverans inom 3 till 5 arbetsdagar av alla varubeställningar över 600 kr!
  • Du kan välja expressleverans i kassan.
  • Beställningar av anpassade delar skickas separat och tar längre tid att behandla och leverera.
  • Oöppnade varor kan returneras mot full återbetalning inom 180 dagar efter att du fått din beställning.
Vissa undantag gäller. Besök vår sida om leveranser och returer för mer information.
TotalbetygAverage rating3.8out of 5 stars
(5 Recensioner)
100% Skulle rekommendera produkten

Betyg

Upplevelse totalt sett

LekupplevelseAverage rating3out of 5 stars
SvårighetsgradAverage rating4out of 5 stars
Valuta för pengarnaAverage rating3.4out of 5 stars
Observera att när du skickar in en röst på en recension samlas din IP-adress in och lagras av vår betrodda tredjepartsleverantör i det enda syftet att förhindra att flera röster läggs från samma IP-adress. Du ser hur du kan skydda dina personuppgifter i vår Sekretesspolicy.

Recensioner

  • September 18th, 2020
    Average rating3out of 5 stars
    Reset button?
    Jag skulle rekommendera produkten till en vän!
    Köpt för: Self
    I bought this sensor to go with my LEGO Powered Up vending machine. It worked excellently, but my machine can feature more than just one gumball! A reset block on the app(if there is, ignore this review) is not featured, so even if I trigger the distance sensor again, it will not function. I have to reset my iPad again manually, which is slightly annoying. The sensor also sometimes triggers when the coin has not passed through the machine, it just doesn’t sense the coin. Please add a reset block on the Powered Up app if there isn’t already, and please steady the sensor detection!
    LekupplevelseAverage rating3out of 5 stars
    SvårighetsgradAverage rating4out of 5 stars
    Valuta för pengarnaAverage rating2out of 5 stars
    Byggtid: 1 tim.
    Byggupplevelse: Intermediate LEGO builder
    Var detta till hjälp?
    35Färg- och avståndssensor
  • February 4th, 2020
    Average rating5out of 5 stars
    Sensor works great, interface a challenge
    | 45-54
    Jag skulle rekommendera produkten till en vän!
    Köpt för: Son
    Bought this (as many do) to make an automatic train (that will stop and wait at stations etc), by placing coloured tiles on the track bed. It is easy to fit to the underside of the passenger train (60197), through the square hold in the baseplate with just a single bracket and the sensor sitting at the same height as the bottom of the bogie. Once I fought the iPad app into submission, the colour sensor (I haven't used the distance feature) worked with a range of coloured tiles, eg red (stop & wait), green (speed up) and yellow (slow down). I had the track on a black tablecloth and have not, so far had any issues with unexpected colour detection. The coding was something of a challenge as you have to handle the idiosyncracies of the sensor with very little guidance (eg the polling frequency of the sensor: once you have detected a colour and performed the action, put in a loop that only exits when that colour changes. Otherwise you can have multiple detections of the same colour leading to unexpected results). Also, in the Mindstorms coding you can have one block to handle multiple possibilities (ie a switch statement) … I haven't found this in the Powered Up interface, and instead have a succession of nested binary "if" blocks.
    LekupplevelseAverage rating3out of 5 stars
    SvårighetsgradAverage rating4out of 5 stars
    Valuta för pengarnaAverage rating5out of 5 stars
    Byggupplevelse: Advanced LEGO builder
    Var detta till hjälp?
    55Färg- och avståndssensor
  • June 28th, 2019
    Average rating5out of 5 stars
    Works 100% with the right colours
    | 35-44
    Jag skulle rekommendera produkten till en vän!
    Köpt för: Self
    Note : Powered Up app needed to use. I have purchased 2 of these from Lego.com and I have fitted one of them to my passenger train 60197, it's in the middle of the loco pointing down at the track, set roughly 5-10mm from the track sleepers. I had to experiment with different colours, red and white were good but yellow was also detected when track went over my laminate flooring. > I use red 4x2 plates on my track in stations stop the train e.g. to load/unload passengers. > I use white 4x2 plates on my track to call sounds and change speed, e.g. horn at tunnel entrance or slow down for a curve With my room/flooring/lighting, all plates are recognised 100% of the time, at hi and low speed, when using red and white plates. I use studded plates as i think the smooth ones are too reflective/shiny. Andy.
    LekupplevelseAverage rating4out of 5 stars
    Valuta för pengarnaAverage rating3out of 5 stars
    Byggtid: 5 min.
    Byggupplevelse: Intermediate LEGO builder
    Var detta till hjälp?
    55Färg- och avståndssensor
  • May 10th, 2019
    Average rating3out of 5 stars
    Distance sensor works great, color sensor iffy
    | 45-54
    Jag skulle rekommendera produkten till en vän!
    I'm using this with the Powered Up hub (88009) to control forward and backward movement of my trains and so far it has been buggy, a combination of both software and hardware issues. The distance sensor function works very well, and you can control the distance of the sensor from an approaching object to kick off a trigger. However, the color sensor has sensitivity issues and is a hit-and-miss (i would say 75% hit 25% miss). It also suffers from sensing a color that is not there. I placed it to read color tiles on a train track and it registers a trigger even if there is no color there. And in order to read a color, the sensor has to be within millimeters of the colored object. Also, not sure if it is with the Powered Up software, but after a few passes of the sensor with colors, it will ignore subsequent color reads and will stop working. I would recommend this for distance sensor control but it needs major improvement with the range and sensitivity of the color sensor. Eventually I would like to make this work on a linear train track on my holiday village to make the train move back and forth controlled by colored tiles.
    Lego

    Svar från LEGO® SHOP

    15 May 2019
    Callie, Customer Service
    Thank you so much for your review! I'm sorry to hear you're having some issues with the Color Sensor. For tip top performance, make sure the sensor is tested in an area with bright and steady lighting while using bricks with varied color values. Black, Brown, Red, Blue and Yellow work the best! Still having trouble tracking the colors? Get in touch with our friendly giving us a shout at LEGO.com/service for some support for your sensor.
    LekupplevelseAverage rating3out of 5 stars
    Valuta för pengarnaAverage rating3out of 5 stars
    Byggupplevelse: Expert LEGO builder
    Var detta till hjälp?
    35Färg- och avståndssensor
...0000000000