Kytke LEGO® Powered Up 88007 Väri ja etäisyysanturi 88006 Move Hubiin tai 88009 Hubiin. Tämä LEGO anturi havaitsee värejä ja liikettä, jotta voit tehdä LEGO rakennelmistasi ja robottileluistasi interaktiivisia.Rakennusohjeet
- Ilmainen vakiotoimitus 5–7 työpäivän kuluessa kaikille yli 55 euron oheistuotetilauksille!
- Pikatoimitus on saatavilla kassalla.
- Yksilölliset osatilaukset lähetetään eri toimituksena kuin oheistuotteet, ja niiden käsittelyyn ja toimitukseen kuluu pidempi aika.
- Avaamattomat oheistuotteet voi palauttaa täyttä hyvitystä vastaan 180 päivän kuluessa tilauksen vastaanottamisesta.
100% Suosittelisi tätä tuotetta
Yleinen arvioAverage rating4out of 5 stars
LeikkikokemusAverage rating3out of 5 stars
VaikeustasoAverage rating4out of 5 stars
Vastinetta rahalleAverage rating3.8out of 5 stars
Huomaa, että kun lähetät hyödyllisen arvion, luotettava kolmannen osapuolen palveluntarjoajamme kerää ja tallentaa IP-osoitteesi. Tarkoituksena on ainoastaan estää useammat lähetykset samasta IP-osoitteesta. Voit tutustua henkilötietojesi valvontaan lukemalla Tietosuojakäytäntömme.
- February 4th, 2020Average rating5out of 5 stars5.0Sensor works great, interface a challengeCrouchEndDad | 45-54Suosittelisin tätä kaverille!Ostettu henkilölle: SonBought this (as many do) to make an automatic train (that will stop and wait at stations etc), by placing coloured tiles on the track bed. It is easy to fit to the underside of the passenger train (60197), through the square hold in the baseplate with just a single bracket and the sensor sitting at the same height as the bottom of the bogie. Once I fought the iPad app into submission, the colour sensor (I haven't used the distance feature) worked with a range of coloured tiles, eg red (stop & wait), green (speed up) and yellow (slow down). I had the track on a black tablecloth and have not, so far had any issues with unexpected colour detection. The coding was something of a challenge as you have to handle the idiosyncracies of the sensor with very little guidance (eg the polling frequency of the sensor: once you have detected a colour and performed the action, put in a loop that only exits when that colour changes. Otherwise you can have multiple detections of the same colour leading to unexpected results). Also, in the Mindstorms coding you can have one block to handle multiple possibilities (ie a switch statement) … I haven't found this in the Powered Up interface, and instead have a succession of nested binary "if" blocks.LeikkikokemusAverage rating3out of 5 stars3.0VaikeustasoAverage rating4out of 5 stars4.0Vastinetta rahalleAverage rating5out of 5 stars5.0Rakennuskokemus: Advanced LEGO builderOliko tästä hyötyä?55Väri- ja etäisyysanturi
- May 10th, 2019Average rating3out of 5 stars3.0Distance sensor works great, color sensor iffyorganista014 | 45-54Suosittelisin tätä kaverille!I'm using this with the Powered Up hub (88009) to control forward and backward movement of my trains and so far it has been buggy, a combination of both software and hardware issues. The distance sensor function works very well, and you can control the distance of the sensor from an approaching object to kick off a trigger. However, the color sensor has sensitivity issues and is a hit-and-miss (i would say 75% hit 25% miss). It also suffers from sensing a color that is not there. I placed it to read color tiles on a train track and it registers a trigger even if there is no color there. And in order to read a color, the sensor has to be within millimeters of the colored object. Also, not sure if it is with the Powered Up software, but after a few passes of the sensor with colors, it will ignore subsequent color reads and will stop working. I would recommend this for distance sensor control but it needs major improvement with the range and sensitivity of the color sensor. Eventually I would like to make this work on a linear train track on my holiday village to make the train move back and forth controlled by colored tiles.15 May 2019Callie, Customer ServiceThank you so much for your review! I'm sorry to hear you're having some issues with the Color Sensor. For tip top performance, make sure the sensor is tested in an area with bright and steady lighting while using bricks with varied color values. Black, Brown, Red, Blue and Yellow work the best! Still having trouble tracking the colors? Get in touch with our friendly giving us a shout at LEGO.com/service for some support for your sensor.LeikkikokemusAverage rating3out of 5 stars3.0Vastinetta rahalleAverage rating3out of 5 stars3.0Rakennuskokemus: Expert LEGO builderOliko tästä hyötyä?35Väri- ja etäisyysanturi
- June 28th, 2019Average rating5out of 5 stars5.0Works 100% with the right coloursMonkeysout | 35-44Suosittelisin tätä kaverille!Ostettu henkilölle: SelfNote : Powered Up app needed to use. I have purchased 2 of these from Lego.com and I have fitted one of them to my passenger train 60197, it's in the middle of the loco pointing down at the track, set roughly 5-10mm from the track sleepers. I had to experiment with different colours, red and white were good but yellow was also detected when track went over my laminate flooring. > I use red 4x2 plates on my track in stations stop the train e.g. to load/unload passengers. > I use white 4x2 plates on my track to call sounds and change speed, e.g. horn at tunnel entrance or slow down for a curve With my room/flooring/lighting, all plates are recognised 100% of the time, at hi and low speed, when using red and white plates. I use studded plates as i think the smooth ones are too reflective/shiny. Andy.LeikkikokemusAverage rating4out of 5 stars4.0Vastinetta rahalleAverage rating3out of 5 stars3.0Rakennusaika: 5 min.Rakennuskokemus: Intermediate LEGO builderOliko tästä hyötyä?55Väri- ja etäisyysanturi
- April 29th, 2020Average rating3out of 5 stars3.0Useful for basic automation of trains, only basicReynard | 25-34Suosittelisin tätä kaverille!Ostettu henkilölle: SelfI played around with this sensor to automate my Lego Trains. It was pretty cool but the system has options (through the Powered Up App) to sense 9 colors (black, blue, green, yellow, red, white, purple, teal, and orange) as well no color. It really only senses 5 of these from what I can tell, none/black, green, yellow, red, and blue. The sensor has a light which is great 'cause if you put it under the trains (I put it in the new version of the cargo train by shifting backward the battery box) it won't have much light. It's really cool 'cause I can automate a lot of stuff with, but since it doesn't really sense the rest of the colors (even when changing the color of the sensor's light) it can't be used as precisely as I'd like. Still, it's not very expensive and the basic hub comes with enough ports for a train motor and a sensor so you don't need more equipment than the sensor to upgrade your setup.
Vastaus LEGO®-kaupasta8 May 2020Emily, Customer ServiceWe're sorry you had some trouble getting your sensor to work with some colors. We'd be happy to help with some troubleshooting. Get in touch at LEGO.build/Service-BV.LeikkikokemusAverage rating2out of 5 stars2.0VaikeustasoAverage rating4out of 5 stars4.0Vastinetta rahalleAverage rating4out of 5 stars4.0Rakennusaika: 5 min.Rakennuskokemus: Advanced LEGO builderOliko tästä hyötyä?35Väri- ja etäisyysanturi